I made a sticker of my blog motto in case anybody needs to advertise their commitment to social isolation. You can download it and print as needed. But if you sell this I will hunt you down and rip your arm hair out with duct tape.
Saturday, March 14, 2020
Thursday, February 27, 2020
New Motor Who Dis?
My 12 year old impact driver seemed worn out so I replaced the motor. That fixed it. This is called cutting to the chase. Here's a link to the part I used. Motor Service Assembly 23-30-0090.
I did some more research into the physics of what exactly is happening in an aging motor. As far as I can tell the issue is that the windings in the motor have a failure of the insulation. They get crammed with carbon dust or other conductive crud which lowers the insulation resistance and pulls more current from the battery. This is why you aren't supposed to use compressed air to blow out a motor housing. All these extra amps are burned up as heat instead of turning into torque. This is basic Ohm's Law logic. Motors are supposed to have a really high insulation resistance. When it starts to fall off then the motor no longer does the same amount of work with the given voltage. None of the sources I found come right out and say this. But that's the manifestation of the issue for me in particular.
My research did reveal that the smell I associate with my grandmother's old Sunbeam mixer creaming butter and sugar for pound cake is actually ozone and vaporized graphite. When my impact driver started making that smell it made me hungry for pound cake, but in fact it should've told me the brushes were breaking down. I always thought worn brushes manifested as an on/off problem. Apparently this other failure mode is also common.
There's a film that forms on the commutator made of copper and carbon and water vapor. It requires the exact right amount of current and humidity to make this protective film that is constantly broken down and reformed. I expect my very humid climate and only using my tool occasionally made it prone to over-filming which lowered the resistance even more, burning off even more of my current as heat, running down my battery really fast without delivering enough torque to get the job done. And also making that smell that makes me think of butter and vanilla.
I have a lot of tools now that are brushless, substituting permanent magnets and microcontrollers for carbon contacts. I will miss the sense memory of my grandmother's kitchen, but I don't have a lot of patience for a tool that won't turn a screw hard enough to pull the work together.
I made a video to show what it's like change the motor in one of these tools. I could've edited it to make it look like I didn't screw it up, but I think that sends the wrong message. Everybody ends up with a part leftover. You have to accept that anything you take apart you're going to have to take it apart again at least once to put back something you missed. Shooting video of the whole thing really helps you figure out exactly where you screwed up.
I did some more research into the physics of what exactly is happening in an aging motor. As far as I can tell the issue is that the windings in the motor have a failure of the insulation. They get crammed with carbon dust or other conductive crud which lowers the insulation resistance and pulls more current from the battery. This is why you aren't supposed to use compressed air to blow out a motor housing. All these extra amps are burned up as heat instead of turning into torque. This is basic Ohm's Law logic. Motors are supposed to have a really high insulation resistance. When it starts to fall off then the motor no longer does the same amount of work with the given voltage. None of the sources I found come right out and say this. But that's the manifestation of the issue for me in particular.
My research did reveal that the smell I associate with my grandmother's old Sunbeam mixer creaming butter and sugar for pound cake is actually ozone and vaporized graphite. When my impact driver started making that smell it made me hungry for pound cake, but in fact it should've told me the brushes were breaking down. I always thought worn brushes manifested as an on/off problem. Apparently this other failure mode is also common.
There's a film that forms on the commutator made of copper and carbon and water vapor. It requires the exact right amount of current and humidity to make this protective film that is constantly broken down and reformed. I expect my very humid climate and only using my tool occasionally made it prone to over-filming which lowered the resistance even more, burning off even more of my current as heat, running down my battery really fast without delivering enough torque to get the job done. And also making that smell that makes me think of butter and vanilla.
I have a lot of tools now that are brushless, substituting permanent magnets and microcontrollers for carbon contacts. I will miss the sense memory of my grandmother's kitchen, but I don't have a lot of patience for a tool that won't turn a screw hard enough to pull the work together.
I made a video to show what it's like change the motor in one of these tools. I could've edited it to make it look like I didn't screw it up, but I think that sends the wrong message. Everybody ends up with a part leftover. You have to accept that anything you take apart you're going to have to take it apart again at least once to put back something you missed. Shooting video of the whole thing really helps you figure out exactly where you screwed up.
Live Oak Tripod Knob
I've sort of forgotten about my blog. I think I'll use it more. I've been doing a lot of YouTube videos and putting way too much information in the description. I should go ahead and put it on my blog.
So here's one. I broke the knob on my good tripod. I made a new knob out of some live oak I harvested from the woods from a long dead snag that has weathered down the the hard hard heart.
I made this last week and used it for several days but today I pushed on it too hard and it slid back on the stem and the glue failed and it spins freely now. So now I'm going to make another, better one. I'll likely make another video and add it here.
This time instead of cutting a knob out of a big blank I found a piece of weathered wood an appropriate diameter. I sliced it and drilled a hole only partway through this time. I polished the sides with nylon brushes on the drill press. I had to drill another smaller hole through the top to let the air out when I epoxied the stem into the knob. I broke two knobs in the process. Glad I started two more after I broke the first one. I think this is going to be a satisfactory knob.
While I was making a big mess on the drill press I polished up several more blanks that I cut at the same time. If anybody wants to try some of this wood to make something I have some ready to sell. Just need to photograph it and weigh it to calculate shipping and I can list it on Etsy.
So here's one. I broke the knob on my good tripod. I made a new knob out of some live oak I harvested from the woods from a long dead snag that has weathered down the the hard hard heart.
I made this last week and used it for several days but today I pushed on it too hard and it slid back on the stem and the glue failed and it spins freely now. So now I'm going to make another, better one. I'll likely make another video and add it here.
This time instead of cutting a knob out of a big blank I found a piece of weathered wood an appropriate diameter. I sliced it and drilled a hole only partway through this time. I polished the sides with nylon brushes on the drill press. I had to drill another smaller hole through the top to let the air out when I epoxied the stem into the knob. I broke two knobs in the process. Glad I started two more after I broke the first one. I think this is going to be a satisfactory knob.
While I was making a big mess on the drill press I polished up several more blanks that I cut at the same time. If anybody wants to try some of this wood to make something I have some ready to sell. Just need to photograph it and weigh it to calculate shipping and I can list it on Etsy.
Subscribe to:
Posts (Atom)